DIY Bath Setup.
DIY Bath Setup.
Blog Article
We've stumbled upon this great article relating to How to Install a Bathtub below on the web and accepted it made good sense to discuss it with you over here.
Installing a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also often, tiling skills. Changing an old bathtub with a brand-new one is also a reasonably challenging task. If the old tub is conveniently available, the task can move easily; if you have to open up a wall to eliminate the old tub and also position the brand-new tub, the task is a lot harder. In either situation, the project is within a house handyman's skills, although you will certainly need an assistant to leave the old tub as well as set in the brand-new one. Ensure you have actually certified yourself for the task and fit attempting it. As opposed to hiring a professional to take over a halfway-completed job, it is better to think about utilizing one before you begin. Opportunities are you may require a professional plumber to make tube connections.
This post will assist you mount a new tub in your washroom if you have already acquired a new tub as well as do not need to alter the setup of your previous water supply pipes.
Your tools and also material checklist must consist of the following:
Preparing for the Setup
To start with, the sustaining structure supplied with the bath must be fitted (if called for) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bathroom, it is additionally sensible to fit a supporting plate under the faucets device to prevent stress on the tub.
Fit the adaptable tap connectors to the bottom of the two faucets making use of 2 nuts and olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and after that pass the electrical outlet via the hole in the bathroom. Use the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washers.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath should now be ready to be fitted in its final position.
Removing Old Taps
If you need to replace old taps with new ones as a part of your installation, then the first thing you should do is disconnect the supply of water. After doing so, turn on the taps to drain any water remaining in the system. The procedure of getting rid of the existing faucets can be fairly bothersome because of the restricted access that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the taps. Have a cloth ready for the continuing to be water that will certainly originate from the pipes. When the supply pipes have actually been gotten rid of, make use of the exact same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this process. Once the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to going on to fit the brand-new taps, compare the pipeline links on the old taps to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Setting up the Bathtub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four small factors.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub until the level reads degree.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints and also new pipework for leakages and tighten them if essential. Fill up the bath tub and also inspect the overflow outlet as well as the normal outlet for leakages.
Lastly, deal with the bath paneling as defined in the producer's user's manual. Tiling as well as securing around the bathtub needs to wait until the tub has been utilized at the very least once as this will certainly settle it right into its last setting.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will certainly need a plastic port to stop damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipes.
If you require to fit a monobloc, then you will call for reducing couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and the sink. Protect the faucet in position with the supplier provided backnut. When the faucet is securely in place, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with regular faucet connectors. The former kind needs to be attached to the tap ends first, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can move enough to break a stiff seal, triggering the water to pass through the wall surface in between the bathroom and the tiling, leading to problems with moisture and possible leaks to the ceiling below.
You can choose from a selection of coloured sealers to assimilate your components as well as fittings. They are offered in tubes and cartridges, and are capable of securing voids approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack fairly very early if you do not take into account this movement prior to securing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently readily available on the marketplace. It is a good idea to fit the ceramic tiles utilizing water-resistant or waterproof glue and also cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a devoted reader about How to Install a Bathtub, I thought sharing that excerpt was worthwhile. Loved our piece of writing? Please share it. Let somebody else check it out. I treasure reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
Course Detail Report this page